Ma-W: 1 revision

2024-04-25T15:20:38Z

1 revision

← Older revision	Revision as of 15:20, 25 April 2024
(No difference)

migrate>Kr-C at 09:16, 20 March 2024

2024-03-20T09:16:35Z

← Older revision		Revision as of 09:16, 20 March 2024
Line 572:		Line 572:

	In certain environments in case of large number of disks (about 100 and more) the zpool move operation can take a long time.		In certain environments in case of large number of disks (about 100 and more) the zpool move operation can take a long time.



	~~=== No support for VMD option in BIOS leads to a problem with listing PCI devices ===~~

	On some servers, an enabled VMD option in BIOS causes that PCI devices are not listed properly. If this is the case please disable the VMD option in BIOS. This problem will be solved in the future release.


Line 600:		Line 594:

	Starting from ZX up29 we no longer support certain 16Gbit FC adapters. If you are using a 16Gbit FC adapter based on the Qlogic chipset using the qla2xxx_scts driver, please refer to our online hardware compatibility list (HCL) to verify if that particular adapter is supported.		Starting from ZX up29 we no longer support certain 16Gbit FC adapters. If you are using a 16Gbit FC adapter based on the Qlogic chipset using the qla2xxx_scts driver, please refer to our online hardware compatibility list (HCL) to verify if that particular adapter is supported.

			Our HCL is available at this link: [https://www.scalelogicinc.com/support/hardware-compatibility-list/Scale Logic-ZX-dss/ https://www.scalelogicinc.com/support/hardware-compatibility-list/Scale Logic-ZX-dss/]

	=== E-mail password cannot contain special non-ASCII characters ===		=== E-mail password cannot contain special non-ASCII characters ===
Line 700:		Line 696:

	According to assumptions, each cluster nodes in Non-Shared storage HA Cluster must have at least one local storage disk before creating the remote disk mirroring path connection.		According to assumptions, each cluster nodes in Non-Shared storage HA Cluster must have at least one local storage disk before creating the remote disk mirroring path connection.

			=== In case of adding or hot-plugging an NVMe disk on one of the cluster nodes in Non-Shared storage HA Cluster this information will not automatically refresh on the remote cluster node. ===

			To resolve this problem, please remove and add remote disks mirroring path connection again on the WebGUI. After the remote disks mirror path connection is re-established, the disks information should be refreshed on both cluster nodes.

	=== In some environments in case of using RDMA for remote disks mirroring path, shutdown one of the cluster nodes may causes its restart instead of shutting down. ===		=== In some environments in case of using RDMA for remote disks mirroring path, shutdown one of the cluster nodes may causes its restart instead of shutting down. ===
Line 786:		Line 786:
	In the case of using the HA Non-Shared storage cluster with compression and deduplication enabled it has been observed that the resilver progress bar on the WebGUI may display values exceeding 100%.		In the case of using the HA Non-Shared storage cluster with compression and deduplication enabled it has been observed that the resilver progress bar on the WebGUI may display values exceeding 100%.

	=== <!-- #~~JBmail 31.10.2023 g. 17:29~~ -->~~Sometimes a web browser may display a blank help page~~. ===		=== <!-- #116234 -->Identification LED blinking does not work on NVMe drives in AMD-based servers. ===

	~~Sometimes a web browser may redirect to the help page using HTTPS, which can result~~ in ~~a blank page being displayed. To resolve this issue, please ensure that your web browser is redirected to the help page using HTTP~~.		The Identification LED blinking on NVMe drives does not work on servers based on AMD processors. This problem will be solved in future releases.

	=== <!-- #~~116234~~ -->~~Identification LED blinking~~ does not ~~work on NVMe drives in AMD-based servers~~. ===		=== <!-- #115416 -->The SED configuration tool available in TUI does not lists devices when using the Broadcom 9600 Storage Adapter. ===

	The ~~Identification LED blinking on NVMe drives~~ does not ~~work on servers based on AMD processors. This problem will be solved in future releases~~.		The SED configuration tool available in TUI does not lists devices when using the Broadcom 9600 Storage Adapter.

	[[Category:Release Notes]]		[[Category:Release Notes]]

Pa-P: 1 revision

2023-12-12T16:02:42Z

1 revision

← Older revision	Revision as of 16:02, 12 December 2023
(No difference)

migrate>Kr-C at 12:18, 6 December 2023

2023-12-06T12:18:44Z

Show changes

Scale Logic ZX ver.1.0 up30 Release Notes - Revision history

Ma-W: 1 revision

migrate>Kr-C at 09:16, 20 March 2024

Pa-P: 1 revision

migrate>Kr-C at 12:18, 6 December 2023